Note: This is the updated plugin adapter to fit MaxxECU STREET, RACE and PRO.
For information on the first generation MaxxECU V1 adapters, downloaded here.
Vehicle |
Engine code |
Year |
LSU sensor |
Note |
Nissan Skyline R32 GTS |
RB25 |
1989 - 1993 |
External sensor needed |
|
Nissan Skyline R32 GT-R |
RB26 |
1989 - 1993 |
External sensor needed |
|
Nissan Skyline R33 GTS-T |
RB25 |
1993 - 1998 |
External sensor needed |
|
Nissan Skyline R33 GT-R |
RB26 |
1993 - 1998 |
External sensor needed |
Note: Manual transmission only!
The MaxxECU adapter for Nissan Skyline R32/33 can be used with all our ECUs
Options |
MaxxECU IO |
STREET |
V1/RACE/PRO |
Fuel pump |
GPO 2 |
Yes |
Yes |
Tachometer |
GPO 8 |
Yes |
Yes |
Boost solenoid |
GPO 3 |
Yes |
Yes |
Vehicle speed |
DIN 1 |
Yes |
Yes |
AC request |
DIN 2 |
Yes |
Yes |
Error light |
GPO 5 |
Yes |
|
Idle solenoid |
GPO 4 |
Yes |
|
AC |
GPO 6 |
Yes |
|
VCT (RB25 only) |
INJ 7 |
Yes |
|
Bluetooth (MDash) |
- |
Yes |
|
Knock sensor(s) |
- |
||
EGT option |
- |
Yes, external |
Yes, direct |
Note: This plugin adapter uses only connector 1 on MaxxECU RACE/PRO units, for extra functionality, the second harness can be added to the RACE ECU.
The PRO ECU have in total of four ECU connectors which could be added for extra functionality: second harness, third harness and/or harness 4.
1 |
MaxxECU CMC connector |
2 |
Vehicle harness adapter |
3 |
16-pin extra connector |
4 |
3-pin extra connector for ex. pressure sensor, analog input 4(AIN 4) |
5 |
2-pin extra connector for external intake temperature sensor (IAT). Not included |
Stock ECU is located behind plastic guard on passenger side floor.
1.Remove the plastic guard where the ECU is located.
2.Disconnect battery from vehicle.
3.Remove and disconnect stock ECU from vehicle harness.
4.Install MaxxECU adapter harness.
5.Route the included MaxxECU MAP-sensor hose to the intake manifold and connect into the MaxxECU.
6.Route wide band lambda cables to exhaust system, install lambda sensor in exhaust and wire the lambda sensor as instructed below.
7.Some models of Nissan Skylines is not equipped with a intake air temperature sensor (IAT) which is recommended to install and connect to the MaxxECU.
1 |
Sensor GND |
2 |
Analog input 4 (0-5v) |
3 |
+5V sensor supply |
see also, analog input.
Note: Pinout is from the wire side of the pre-wired cable harness.
Pin |
Description |
Usage |
Note |
1 |
Wide band (VREF) |
|
|
2 |
Wide band (VS) |
|
|
3 |
Wide band (shield) |
|
|
4 |
Wide band (H-) |
|
|
5 |
GPO 7 / DIN 3 |
Not available on MaxxECU STREET |
|
6 |
- |
|
|
7 |
- |
|
|
8 |
INJ 8 |
Not available on MaxxECU STREET |
|
9 |
Wide band (IP) |
|
|
10 |
Wide band (RCAL) |
|
|
11 |
+12V |
Output |
|
12 |
+12V |
Output |
|
13 |
Engine GND |
|
|
14 |
AIN 1 |
||
15 |
AIN 2 |
||
16 |
AIN 3 |
LSU 4.2 wiring with MaxxECU Plugin solutions.
Note: Seen from the wire side of the pre-wired connector.
PIN |
Function (LSU 4.2) |
1 |
VS |
2 |
RCAL |
3 |
+12V |
4 |
H- |
5 |
VREF |
6 |
IP |
See also external wide band lambda wiring.
Some vehicles are not equipped with an intake air temperature (IAT) sensor and MaxxECU plugin solutions do have the
option to add a sensor.
The intake air temperature (IAT) sensor should be mounted to sense fresh air flow going into the engine.
Depending on the intake manifold construction, the position of the temperature sensor is not given, but preferably mount
the sensor in the intake, or in the pipe before/after the throttle.
MaxxECU plugin solution are equipped with an optional 2-pin connector for optional IAT wiring.
Mating connector and wires for external IAT sensor.
Example wirings of extra input and output
Last updated: 2017-03-15 by Natanael Ceder